You should be aware that this is measured on the diagonal, and since we have been using those numbers throughout, you should assume that this is the case. This is the very first instance of its kind ever seen. Does this sound like something we ought to pull out and take a look at in order to assess what we have available? It depends on. In any case, you need to take this to mean that this is your normal value.

A value of 0.49 describes this situation. The diagonal measurement should be a half an inch, if everything checks out. So, we're at zero here.

49, which makes me think that this is the smallest of them all,Then I came across this one, which is on the shorter side, so for the time being we will refer to it as 16 years old. Let me see, this is a 64 by 32, of course, this is a 128 by 64, which indicates that it is a quarter of the side that is 64 by 32. Let me look at this again. As a result of the actual reduction in size of the screen, there is now a point that is equal to approximately 7/16 of an inch, which is designated as the half point. This one has a better layout, but it only has a half point because the other one only has a half point. OK, so there is a half point, but the layout isn't very good. As a result, the device as a whole is more compact, but the screen on this one is physically more condensed. Permit me to take a look because, despite the fact that the screen is on the lower end of the size spectrum, it seems to be of very high quality. In point of fact, I think that it is forty by seventy, which is a pixel, and this is zero. In other words, it is a zero pixel.

 

 

 

20220429092827_18007.jpg



96, this is 12864, this is 0. 49, this is 6432, and then this is 70 x 40, which is 0. 42; therefore, this actually has a higher resolution than those other numbers. 96, this is 12864, this is 0. 49, this is 6432, and then this is 70 x 40, which is 0. 42. The SPI interface can be found here, and the ITC interfaces can be found here and here. OK. Let's give welding a shot now that we have everything assembled as it should be.

Alright, let's start making a mess with the welding. Okay, the first thing I have to do is position it roughly where I want it, and after that I need to solder it into position. After that, I'll proceed to the following stage in the process. The welding plate would not go any lower despite my best efforts. Even though it was only a short distance, we decided to walk. This technique is referred to as "welding with bare hands."Due to the fact that OLED manufacturers appears to be crooked now that I examine it more closely, I will have to keep my hand on it.

That one appears to have a lot of potential appeal. It makes an already difficult situation even more challenging. OK, good. At this point, I will solder the other end, which is located here. I will put it in place until we finish working here to achieve this goal, and I will make sure that it is done in the correct manner. Therefore, it amounts to the same thing. Please place the additional piece of solder in the right spot before we move on to the next step. Another piece of solder has been provided. Take into consideration the fact that this may be somewhat more demanding.

Shall we embark on this journey together? Yes, it seems like they are in good shape; however, we need to check to see if there are any coal joints. There is not a single type of joint that is more unpleasant than smoking a cold one. Make it presentable. Good. Have you taken the time to observe that there is a sizeable gap there? Why don't you just come out and say that there's no way that there can be a gap between us and the other team? It is impossible for there to be such a gap between us.

 

20200926025706_44445.jpg

 


Oh, what a wonderful change—the sharpness of the vision! This is an encouraging new turn of events. When it comes to maintenance, fixing the good stuff is almost always the most challenging. After you've made a mess of things for them, I think we'll be in a position to put some pressure on the situation here. Please be as passionate as possible. Let's get started, and once we've done that, we need to put everything in its proper place. I have to queue up.

It is a significant step forward.    It is a significant step forward.   It is a significant step forward.   It is a significant step forward.   I didn't get around to beginning it until much later, and by the time I did, the instructions needed to be rewritten. It's I2C. I am obligated to carry it out right now due to the fact that I have never done it before.

On the other hand, things have reached an absurdly high level. It is very inconvenient for me in many different ways. Which version of SSD 1306 are we currently working with? It will be possible to run the program due to the fact that the memory was intended to function at 12864, which is the function of the memory. However, the resolution is only 128 by 64, despite the fact that it will function correctly. Okay, but the problem is that these little guys do not use the entire memory; as a consequence, they are present in the memory; as a consequence, you need to center it on your X axis, and then on your Y axis, you need to tell it that it is on the top.

This is a matter of the utmost importance. You will need to use this function in order to change the display mode, as it is currently set to the opposite of what it should be. After I give it a flip, it will move to this position further down. It appears that rather than images, it is displaying all of these arbitrary data here, but I have no idea why this is happening. I choose not to make use of it in this context due to the fact that it has been muted, which has led to a chaotic circumstance. After I get the correct geometry stored in the memory of SSD 1306, I immediately run these things.

I don't like it. It is insufficient in size. One of the reasons I do not like it is because it has a big board, which is another reason why I do not like it. It was organized in a very sluggish manner. Then, take a look at what I have here. The trip got under way.

This represents the highest possible level of brightness. I have given it every thought I can muster in the hopes that it will comply with the instruction to change the level of brightness, but to no avail. The effect of this one isn't all that great, but I'm not sure if you can see it because it's so subtle. In spite of that, I would say that, all things considered, this is the option that appeals to me the most. It's 0. 49. This one is extremely useful in its application.

It emits a light that is very bright. This one has a terrible structure in terms of its organizational makeup. It is insensitive to changes in the amount of illumination that is present. For this reason, I have faith that we will come back.

Let's come full circle and discuss this issue again. OK, I believe everything is ready to go, and I ought to be able to photograph this. This is an exceptionally high-quality small OLED, and it can be purchased for just a few dollars. Due to this reason, I will also discuss the software within the description. You can get it.